Thermoplastic Marking Paint
Home > Products > Road Markings > Thermoplastic Marking Paint
  • Thermoplastic Marking Paint

  • Thermoplastic Marking Paint

  • Thermoplastic Marking Paint

  • Thermoplastic Marking Paint

  • Thermoplastic Marking Paint

  • Thermoplastic Marking Paint

Thermoplastic Marking Paint

Item Code: GMP-TP-01

  • Feature
  • Technical Data
  • Application
  • Package

Go Green thermoplastic reflective marking paint is a kind of paint applied on the road to make the road marking. Its mainly consist of petroleum resin, EVA, PE wax, pigment fillers materials, its powder state in normal temperature, need to heat in hot-melt kettle to 180-200℃, keep heat preservation while stirring for 3-5 minutes, then apply on pavement to form a solid coating. It has the characteristics of full linearity and strong wear resistance, during construction, spread reflective beads (dosage 18-25%) on the surface, it has good reflective effect at night. Thermoplastic reflective marking paint is widely applied on highway, city street etc. Common used standards are National Standard, British Standard and American Standard.


Product Characters


1. Strong Adhesion

The resin content is reasonable, special rubber elastomer is added to the base oil, super strong adhesion to ensure the construction is good without obscission


2. Good Anti-cracking

Hot-melt marking is prone to crack because of temperature difference. Add enough EVA resin to coatings to prevent cracking.


3. Bright Color

Using top-grade coated pigments with reasonable proportion and good weather resistance, won't change color under long-term sun exposure



4. High Coating Rate

Small density, large volume and high coating rate are our product main characteristics


5. Good Anti-fouling

The PE wax quality and dosage are the key factors to affect the anti-fouling performance. Exxon PE wax is the our preferred product for many years.




Product Index 


NameThermoplastic Reflective Marking Paint
Package25kg
Application RangeVarious traffic road, airport, terminals etc places
Quality StandardISO9001 JT/T280-2004
Heating Temperature180-220℃
Available ColorWhite, Yellow, Blue, Red etc
Production Capacity60000 Tons
Product PerformanceStrong adhesion, bright colour, anti-fouling, anti-cracking, high coating rate



Dosage



Powder WeightCoating ThicknessCoating AreaPrimer DosageBeads Dosage
1T1.8mm22532kg100kg



Attention


1. Ensure the pavement is dry and clean, if raining, after 4 hours sun exposure then start the construction, temperature should be above 0℃ 


2. Heaing the powder to 180-200℃, after melting, it should be stirred uniformly and keep 3-5 minutes before discharging. Once the coatings are ready, it should be apply on road immediately to avoid small fires keeping warm for a long time, that will cause precipitates. 


3. The base oil should be treated sufficiently, after the base oil is completely dry then spread the marking paint. 


4. For the new built concrete pavement, the construction should be delayed for three months or the bottom oil treatment should be carried out twice, otherwise the marking line will fall off easily. 


5. For the high traffic flow section, protect the area after coating the base oil to avoid any vehicles passing by.


Construction 


1. Clean the road: firstly remove the road surface debris, use road wind power cleaner to clean road surface to meet the road marking construction requirements.


2. Construction lofting: within the construction scope, survey and measure the road line according to construction drawings and technical requirement to control the standard. After complete the lofting, doing the preliminary inspection, once its qualified, then process to next working procedure.


3. Using high pressure airless spraying equipment to spray the primer coating, then spray the thermoplastic road marking paint, at the same time, spread the glass beads, ensure the painting line is smooth, straight, beautiful, uniformly thickness, good reflective function etc standard.


4. Ending Work: Place warning signs to prevent cars and pedestrians from rolling the constructed markings. The road marking project routeline is long, although the drying time is soon about three minutes, but it is easy to be disturbed by other construction units, so the protection should be strengthened in construction. Vehicles should not be allowed to pass before completely drying.



Product NamePhotoDescriptionContainer Loading
Thermoplastic Marking PaintThermoplastic Marking Paint

Go Green thermoplastic reflective marking paint is a kind of paint applied on the road to make the road marking.

Its mainly consist of petroleum resin, EVA, PE wax, pigment fillers materials

25kg/bag, a 20ft container load 25 tons




Online Inquiry

Kindly fill up the inquiry form, we will deal with your inquiry within 24 hours.

Product Name: Thermoplastic Marking Paint

Name:
Country:
Company:
E-mail:
Tel.:
Website:
Your Message:
CAPTCHA:
Contact Us
  • Go Green Industrial (Shanghai) Co.,Ltd.
  • Phone: +86 21 6105 3027 / 6100 9307
  • Mobile: +86 159 0079 5274
  • Fax: +86 21 5187 6819
  • E-mail: sales@go-green.com.cn
  • Add: 12th Floor, YongYe Mansion. No.2240 South Pudong Road, Pudong New District. Shanghai, China 200127